CT—C型系列熱風循環烘箱配用低噪音耐高溫軸流風機和自動控溫系統,整個循環系統全封閉,使烘箱的熱效率從傳統的烘房3-7%提高到目前的35-45%,最高熱效率可達70%。 GT-C型熱風循環烘箱的設計成功,使我國的熱風循環烘箱達到了國內外先進水平。為我國節約了大量能源,提高了企業的經濟效益。
CT—C型系列熱風循環烘箱配用低噪音耐高溫軸流風機和自動控溫系統,整個循環系統全封閉,使烘箱的熱效率從傳統的烘房3-7%提高到目前的35-45%,最高熱效率可達70%。 GT-C型熱風循環烘箱的設計成功,使我國的熱風循環烘箱達到了國內外先進水平。為我國節約了大量能源,提高了企業的經濟效益。
設備簡介Equipment Introduction
CT—C型系列熱風循環烘箱配用低噪音耐高溫軸流風機和自動控溫系統,整個循環系統全封閉,使烘箱的熱效率從傳統的烘房3-7%提高到目前的35-45%,最高熱效率可達70%。 GT-C型熱風循環烘箱的設計成功,使我國的熱風循環烘箱達到了國內外先進水平。為我國節約了大量能源,提高了企業的經濟效益。
The CT-C series hot air circulation oven is equipped with a low-noise and high-temperature resistant axial flow fan and an automatic temperature control system. The entire circulation system is fully enclosed, increasing the thermal efficiency of the oven from the traditional drying room of 3-7% to the current 35-45%, with a maximum thermal efficiency of 70%. The successful design of the GT-C hot air circulation oven has enabled China's hot air circulation oven to reach advanced levels both domestically and internationally. It has saved a lot of energy for our country and improved the economic efficiency of enterprises.
工作原理operational principle
熱風循環烘箱空氣循環系統采用風機循環送風方式,風循環均勻高效。風源由循環送風電機(采用無觸點開關)帶動風輪經由加熱器,而將熱風送出,再經由風道至烘箱內室,再將使用后的空氣吸入風道成為風源再度循環,加熱使用。確保室內溫度均勻性。當因開關門動作引起溫度值發生擺動時,送風循環系統迅速恢復操作狀態,直至達到設定溫度值
The air circulation system of the hot air circulation oven adopts a fan circulation air supply method, with uniform and efficient air circulation. The air source is driven by a circulating air supply motor (using a contactless switch) to drive the wind wheel through the heater, which sends hot air out and then through the air duct to the interior of the oven. The used air is then sucked into the air duct to become the air source for further circulation and heating. Ensure uniformity of indoor temperature. When the temperature value fluctuates due to the action of opening and closing the door, the air supply circulation system quickly resumes operation until the set temperature value is reached
設備特點Equipment characteristics
大部分熱風在箱內循環,熱效率高,節約能源。
利用強制通風作用,箱內設有可調式分風板,溫度平衡。
熱源可采用蒸汽、熱水、電、遠紅外,選擇廣泛 。
整機噪音小,運轉平衡,溫度自控,安裝維修方便。
適用范圍廣,可干燥各種物料,是通用干燥設備。
Most of the hot air circulates inside the box, with high thermal efficiency and energy savings.
By utilizing forced ventilation, there is an adjustable air distribution plate inside the box, ensuring temperature balance.
The heat source can be steam, hot water, electricity, and far-infrared, with a wide range of options.
The whole machine has low noise, balanced operation, temperature control, and convenient installation and maintenance.
It has a wide range of applications and can dry various materials, making it a universal drying equipment.
應用范圍Application scope
熱風循環烘箱適用于制藥、化工、食品、農副產品、水產品、輕工、重工等行業物料及產品的加熱固化、干燥脫水。如原料藥、生藥、中藥飲片、浸膏、冊劑、顆粒、沖劑、水丸、包裝瓶、顏料染料、脫水蔬菜、瓜果干、香腸、塑料樹脂、電器原件、烘漆等。也適用于烘烤有化學性氣體,油墨的固化、漆膜的烘干等,還適用于電子、電機、通訊、電鍍、塑料、五金化工、儀器、印刷、制藥、PC板、粉體、含浸、噴涂、玻璃、木器建材等等的精密烘烤、烘干、回火、預熱、定型、加工等;內熱循環,烘烤物件受熱均勻。
The hot air circulation oven is suitable for heating, solidification, drying, and dehydration of materials and products in industries such as pharmaceuticals, chemicals, food, agricultural and sideline products, aquatic products, light industry, and heavy industry. Such as raw materials, raw medicines, traditional Chinese medicine decoction pieces, extracts, formulations, granules, granules, granules, water pills, packaging bottles, pigments and dyes, dehydrated vegetables, dried fruits and vegetables, sausages, plastic resins, electrical components, baking paints, etc. It is also suitable for precise baking, drying, tempering, preheating, shaping, and processing of chemical gases, ink curing, paint film drying, as well as electronics, motors, communications, electroplating, plastics, hardware and chemical engineering, instruments, printing, pharmaceuticals, PC boards, powders, impregnation, spraying, glass, wood and building materials, etc; Internal heat circulation ensures even heating of baked goods.
設備結構Equipment structure
1、熱風循環烘箱由角鋼、不銹鋼板以及冷鋼板構成。
2、保溫層則由高密度硅酸鋁棉填充,高密度硅酸鋁棉保證了烘箱的保溫性,也確保了使用者的安全性。
3、加熱器安裝位置可是底部、頂部或兩側。
4、用數顯智能儀表來控制溫度。熱風循環烘箱風道設計有兩種:水平送風和垂直送風!
1. The hot air circulation oven is composed of angle steel, stainless steel plate, and cold steel plate.
2. The insulation layer is filled with high-density aluminum silicate cotton, which ensures the insulation of the oven and the safety of the user.
3. The installation position of the heater can be at the bottom, top, or both sides.
4. Use digital intelligent instruments to control temperature. There are two types of air duct designs for hot air circulation ovens: horizontal air supply and vertical air supply!
主要技術參數及說明Main technical parameters and instructions
加熱熱源蒸汽、電、遠紅外,電蒸汽兩用,供用戶選擇。
使用溫度:蒸汽加熱50-140度,最高150度。
用電、遠紅外溫度50-350度。
備有自控系統和電腦控制系統供用戶選擇。
常用蒸汽壓力0.02-0.8Mpa(0.2-8Kg/cm2) 。
配用電加熱按Ⅰ型計算15Kw,實用5-8Kw/h。
特殊要求在定貨時表明。
使用溫度大于140度或小于60度,要在訂貨時注明。
出廠烘車烘盤尺寸統一,可以互換。
熱風循環烘箱應用的范圍很廣泛,可干燥各種工業物料,是通用的干燥設備,一般熱風循
環烘箱溫度范圍為室溫 ~ +250℃,高溫型為室溫 ~ +500℃。
烘盤尺寸:460×640×45mm
Heating source steam, electric, far-infrared, dual-purpose electric steam for users to choose from.
Usage temperature: Steam heating 50-140 degrees, maximum 150 degrees.
Electricity consumption, far-infrared temperature of 50-350 degrees.
Equipped with automatic control systems and computer control systems for users to choose from.
The commonly used steam pressure is 0.02-0.8Mpa (0.2-8Kg/cm2).
Equipped with electric heating, calculated as 15Kw according to Type I, practical 5-8Kw/h.
Special requirements should be indicated when placing an order.
If the operating temperature is greater than 140 degrees or less than 60 degrees, it should be specified when placing an order.
The size of the baking tray for the factory drying car is uniform and interchangeable.
The application range of hot air circulation oven is very wide, which can dry various industrial materials and is a universal drying equipment. Generally, hot air circulation
The temperature range of the ring oven is from room temperature to+250 ℃, and the high-temperature type is from room temperature to+500 ℃.
Oven size: 460 x 640 x 45mm
主結構示意圖Main structure schematic diagram
設備配件Equipment accessories
技術參數表Technical parameter table
行業標準型號Industry standard models | 型號model | 干燥量Drying capacity | 功率power | 耗用蒸汽Steam consumption | 散熱面積Heat dissipation area | 風量Air volume | 上下溫差Temperature difference between upper and lower parts | 烘盤baking pan | 長*寬*高length*width*height | 烘車Drying car |
RXH-14-B | CT-Ⅰ | 120kg/batch | 1.1kw | 20kg/h | 20㎡ | 2800m3/h | ±2℃ | 48個 | 2430×1200×2375mm | 2 |
RXH-27-B | CT-Ⅱ | 240kg/batch | 2.2kw | 40kg/h | 40㎡ | 5200m3/h | ±2℃ | 96個 | 2430×2200×2433mm | 4 |
RXH-41-B | CT-Ⅲ | 360kg/batch | 3kw | 60kg/h | 80㎡ | 8000m3/h | ±2℃ | 144個 | 3430×2200×2620mm | 6 |
RXH-54-B | CT-Ⅳ | 480kg/batch | 4kw | 80kg/h | 100㎡ | 9800m3/h | ±2℃ | 192個 | 4460×2200×2620mm | 8 |
RXH-5-C | CT-C-O | 25kg/batch | 0.45kw | 5kg/h | 5㎡ | 3450m3/h | ±2℃ | 16個 | 1130×1100×1750mm | 0 |
RXH-7-C | CT-C-ⅠA | 50kg/batch | 0.45kw | 10kg/h | 10㎡ | 3450m3/h | ±2℃ | 24個 | 1400×1200×2000mm | 1 |
RXH-14-C | CT-C-Ⅰ | 120kg/batch | 0.45kw | 18kg/h | 20㎡ | 3450m3/h | ±2℃ | 48個 | 2300×1200×2000mm | 2 |
RXH-27-C | CT-C-Ⅱ | 240kg/batch | 0.9kw | 36kg/h | 40㎡ | 6900m3/h | ±2℃ | 96個 | 2300×2200×2000mm | 4 |
RXH-27A-C | CT-C-ⅡA | 240kg/batch | 0.9kw | 36kg/h | 40㎡ | 6900m3/h | ±2℃ | 96個 | 4460×1200×2290mm | 4 |
RXH-41-C | CT-C-Ⅲ | 360kg/batch | 1.35kw | 54kg/h | 80㎡ | 10350m3/h | ±2℃ | 144個 | 3430×2200×2000mm | 6 |
RXH-42A-C | CT-C-ⅢA | 360kg/batch | 1.35kw | 54kg/h | 80㎡ | 10350m3/h | ±2℃ | 144個 | 2300×3200×2000mm | 6 |
RXH-54-C | CT-C-Ⅳ | 480kg/batch | 1.8kw | 72kg/h | 100㎡ | 13800m3/h | ±2℃ | 192個 | 4460×2200×2290mm | 8 |