LMSZ雙錐真空干燥機是我廠在結合國內同類產品技術所開發的新一代干燥裝置,雙錐真空采用皮帶--鏈條兩彈性聯接方式,因而設備運行平穩。特別設計的工藝,充分體現了兩支軸的良好同心,熱媒及真空系統均采用可靠的機械密封或美國技術的旋轉接頭。在此基礎上,我們開發了LMSZ-A既可無級調速,又能進行恒溫控制。
設備簡介Equipment Introduction
LMSZ雙錐真空干燥機是我廠在結合國內同類產品技術所開發的新一代干燥裝置,雙錐真空采用皮帶--鏈條兩彈性聯接方式,因而設備運行平穩。特別設計的工藝,充分體現了兩支軸的良好同心,熱媒及真空系統均采用可靠的機械密封或美國技術的旋轉接頭。在此基礎上,我們開發了LMSZ-A既可無級調速,又能進行恒溫控制。
作為專業干燥設備制造廠,本廠產品從高溫導熱油為熱媒介質、中溫蒸汽及低溫熱水一應俱全。干燥粘性物料時,本廠將在罐內為您特別設計"抄板"機構或設置滾珠。
The LMSZ double cone vacuum dryer is a new generation drying device developed by our factory in combination with similar domestic product technologies. The double cone vacuum adopts a belt chain elastic connection method, so the equipment runs smoothly. The specially designed process fully reflects the good concentricity of the two shafts, and the heating medium and vacuum system both use reliable mechanical seals or American technology rotary joints. On this basis, we developed LMSZ-A, which can achieve both stepless speed regulation and constant temperature control.
As a professional drying equipment manufacturer, our products range from high-temperature heat transfer oil as the thermal medium, medium temperature steam, and low-temperature hot water. When drying sticky materials, our factory will specially design a "copying plate" mechanism or set up rolling balls in the tank for you.
工作原理operational principle
l 在密閉的夾層中通入熱能源(如熱水,低壓蒸汽或導熱油),熱量經內殼傳給被干燥物料。
l 在動力驅動下,罐體作緩慢旋轉,罐內物料不斷地混合,從而達到強化干燥的目的。
l 物料處于真空狀態,蒸汽壓下降使物料表面的水份(溶劑)達到飽和狀態而蒸發了,并由真空泵及時排出回收。
l 物料內部的水份(溶劑)不斷地向表面滲透、蒸發、排出三個過程不斷進行,物料在很短時間內達到干燥目的。
l Heat energy (such as hot water, low-pressure steam, or thermal oil) is introduced into a closed interlayer, and the heat is transferred to the dried material through the inner shell.
l Under power drive, the tank rotates slowly and the materials inside the tank continuously mix, thereby achieving the goal of strengthening drying.
l The material is in a vacuum state, and the decrease in vapor pressure causes the water (solvent) on the surface of the material to reach saturation and evaporate, which is promptly discharged and recovered by a vacuum pump.
l The water (solvent) inside the material continuously permeates, evaporates, and is discharged from the surface, achieving the drying goal in a short period of time.
應用范圍Application scope
適用化工、制藥、食品等行業的粉狀、粒狀及纖維的 濃縮、混合、干燥及需低溫干燥的物料(如生化制品等).更適用于易氧化、易揮發、熱敏性、強烈刺激、有毒性物料和不允許破壞結晶體的物料的干燥。
Suitable for the concentration, mixing, drying, and low-temperature drying of powdered, granular, and fiber materials in industries such as chemical, pharmaceutical, and food. It is more suitable for drying materials that are prone to oxidation, volatilization, heat sensitivity, strong irritation, toxic substances, and materials that do not allow crystal damage.
設備特點Equipment characteristics
l 油加熱時.采用自動恒溫控制.可以干燥生化制品
l 和礦物原料,溫度可在20~160oC之間。
l 熱效率高,比一般烘箱提高2倍以上。
l 間接加熱.物料不會被污染,符合“GMP”要求。設備維修操作簡便,易清洗。
l When heating oil, automatic constant temperature control is adopted, which can dry biochemical products
l The temperature of mineral raw materials can be between 20-160oC.
l High thermal efficiency, more than twice that of a typical oven.
l Indirect heating. The material will not be contaminated and meets GMP requirements. The equipment maintenance operation is simple and easy to clean.
技術參數表Technical parameter table
型號model | LMXZ -100 | LMXZ -350 | LMXZ -500 | LMXZ -750 | LMXZ -1000 | LMXZ -1500 | LMXZ -2000 | LMXZ -3500 | LMXZ -4500 | LMXZ -5000 |
罐內容積 Tank volume | 100L | 350L | 500L | 750L | 1000L | 1500L | 2000L | 3500L | 4500L | 5000L |
裝料容積 Loading volume | ≤50L | ≤175L | ≤250L | ≤375L | ≤500L | ≤750L | ≤1000L | ≤1750L | ≤2250L | ≤2500L |
加熱面積 Heating area | 1.16㎡ | 2㎡ | 2.63㎡ | 3.5㎡ | 4.61㎡ | 5.58㎡ | 7.5㎡ | 11.2㎡ | 13.1㎡ | 14.1㎡ |
轉速speed | 4 - 6r/min | |||||||||
電機功率 Motor power | 0.75kw | 1.1kw | 1.5kw | 2kw | 3kw | 3kw | 4kw | 5.5kw | 7.5kw | 11kw |
占地面積長寬 Floor area length and width | 2160× 800mm | 2260× 800mm | 2350× 800mm | 2560× 1000mm | 2860× 1300mm | 3060× 1300mm | 3260× 1400mm | 3760× 1800mm | 3960× 2000mm | 4400× 2500mm |
回轉高度 Rotating height | 1750mm | 2100mm | 2250mm | 2490mm | 2800mm | 2940mm | 2990mm | 3490mm | 4100mm | 4200mm |
罐內設計壓 Design pressure inside the tank | -0.1-0.15MPa | |||||||||
夾套設計壓力 Design pressure of jacket | ≤0.3MPa | |||||||||
工作溫度 operation temperature | 罐內≤85℃ 夾套≤140℃ Inner tank ≤ 85 ℃, jacket ≤ 140 ℃ | |||||||||
用冷凝器時 的真空泵型號 Vacuum pump model when using condenser | 2X-15A | 2X-15A | 2X-30A | 2X-30A | 2X-70A | JZJX 300-8 | JZJX 300-4 | JZJX 600-8 | JZJX 600-4 | JZJX 300-4 |
功率power | 2KW | 2KW | 3KW | 3KW | 505KW | 7KW | 9.5KW | 11KW | 20.5KW | 22KW |
不用冷凝器時 的真空泵型號 Vacuum pump model when not using condenser | SK-0.4 | SK-0.8 | SK-0.8 | SK-2.7B | SK-2.7B | SK-3 | SK-6 | SK-6 | SK-9 | SK-10 |
功率power | 1.5KW | 2.2KW | 2.2KW | 4KW | 4KW | 5.5KW | 11KW | 11KW | 15KW | 18.5KW |
重量weight | 800kg | 1100kg | 1200kg | 1500kg | 2800kg | 3300kg | 3600kg | 6400kg | 7500kg | 8600kg |
注:對干燥前后容積變化很大的物料,其裝料系數可適當加大或縮小。
Note: For materials with significant volume changes before and after drying, their loading coefficient can be appropriately increased or reduced.